Replacement Locks For Patio Doors at Lowe's
Replacing the patio door lock is a simple and effective way to enhance the security of your home. But, it is important to maintain the lock regularly and install the lock properly.
It is important to identify the type of patio door lock that you have to replace it successfully. You can identify the type by looking at the size of the screw hole and the type of face plate at the end.
Identifying your existing lock
It is important to understand the differences between different types of locks before you decide to purchase new hardware for your lock. This will enable you to choose a lock that is ideal for your home, and also ensure its safety and security.
The most commonly used lock is one that is a cylinder lock. It's also called pin-and-tumbler lock. This lock style uses a combination bottom pins springs, top pins, and top pins to secure the keyhole and plug. Cylinder locks come in different sizes. It is important to determine the length and diameter of the cylinder you have before buying a new one.
To determine the width to determine the width, loosen the screws that keep the cylinder in place and then carefully remove it. Then, take a measurement of the distance between the outer edge of the cylinder and its inner edge and note the measurement in millimeters. Then, you can compare this measurement with the measurements of the new lock you're planning on buy. This will ensure that your new lock will fit in the existing door lockhole.
Another way to determine the correct size of your lock is to test it by using a key. If the key can slide into the cylinder easily and easily, then it is the size of the rekeying kit you need. If the key will not slide into the cylinder your cylinder could have a different keyway and therefore cannot be rekeyed to accept that brand of key.
It is always best to read the manufacturer's instructions that accompany a rekey kit for each lock, since each lock comes with its own set of installation requirements. It is important to test the new lock thoroughly following installation to ensure that it functions properly and offers you maximum security. Also, pay attention to the additional features of the new lock, as these can affect its ease of use.
Measure the Width
A patio door lock that's not working properly can cause serious security problems. It is essential to check regularly your locks and replace them when needed. This helps ensure they are safe and working correctly, and could aid in preventing issues like a loose latch or keyway. Lowe's has new locks that can provide your home with the security it needs, whether your existing locks are worn or damaged.
It is essential to measure the door to your patio before purchasing the new lock. This will help you to determine the size of lock you should purchase and avoid the possibility of purchasing a lock that does not fit. There are two measurements you need to accomplish this: the backset and the depth of the case. The first is a distance between the edge of a lock's face and the centre of the hole through which the handle spindle goes through. The second refers to looking at the depth of an lock from the outside.
It's also important to think about how you will be using your doors before deciding on the kind of lock you require. If your sliding doors open horizontally you will need top and bottom tab locks that engages with the strikeplate, preventing it from being lifted or forcefully opened. If your patio doors are vertically open, you'll need to choose mortise latches that have an attached hook latch that is spring loaded to provide additional security.
It is important to know the location of the screw holes when determining the dimensions of your lock. Some mortise lock screws will be round, while others are square. You'll need to know where the keyway is located. Some locks have a vertical keyway while others are 45-degree angled. Take a photo of the lock using a digital camera to ensure that you get the right replacement.
Once you've taken your measurements, it's now time to search for an updated patio door lock. There are a variety of high-quality locks online and many of them are branded with advanced security features to protect your home. It's important to compare locks and read reviews prior to you make a purchase. Don't forget to maintain your locks regularly to prevent dirt and other debris from blocking your doors.
Be aware of the screw holes
Patio doors are an important part of your home's security. They must be inspected for signs of wear and tear to ensure they function correctly. Over time the spindle and locks that connect your interior and exterior handles may need to be replaced. A strong lock will not only to prevent intrusion but also improve security, energy efficiency, and security.
If you aren't sure of the exact type of lock your patio door has, there are several ways to narrow down your search for a replacement. First, try to identify the type of keyway it uses. replace lock on upvc door are commonly used in aluminum patio doors, while E2126 and E2079 locks sit in a recess within the frame of wood or vinyl patio doors. If you have a digital camera, uploading a photo of the lock can help you determine what kind of lock it is.
Another way to determine the type of lock you have is to look at the screw holes. The screw holes on the majority of sliding patio door locks are aligned with the latch keeper that is mounted on the side jamb. However they may not be the same. Some screws may be longer than others, or have a different threaded finish. Some screws are equipped with washers or a hexagonal nut attached, which can change the way they fit into the lock's hasp.
Once you have a clear idea what type of lock you own it's time to begin planning to install the new lock. The first step is to clean the lock with a damp cloth or brush to get rid of any debris or dirt that could be affecting its operation. After you've cleaned the lock, apply a silicone-based oil to keep the locking mechanism in good shape and quiet.
After that, it's a great idea to replace the old screws with more long ones. This will help you to get an improved grip, and install the lock more easily. After you've completed that, it's a good idea to test the handle and see how the latch engages in the lock.
If it doesn't engage easily You may have to install a washer or hex nut behind the hasp to allow it to be able to grip more of the door's lip. You can even add a shim to the side of the lock keeper that is on the jamb to see if that helps.
Check the Lock Snib
The snib or mechanism for locking, is located inside the door handle. You can engage and disengage the snib to open and close your patio doors. It is the first thing to check when your locks aren't functioning properly. You can also check the keepers located at the top and bottom of the door frames to see if there is any misalignment or looseness which could cause them to break. Make sure that your snib lock is correctly seated and that the lock hasn't been blocked or stuck in any other way.
The most commonly used patio door locks are steel mortise locks that lock sliding glass doors. They are inserted into the frame of the door and are available in various styles, making them an effective security measure. Some are designed to hold keys, while some utilize an oval cutout to allow easy locking and unlocking.
Another popular option is a thumb-screw-style step-on lock that securely keeps your sliding doors in place, without requiring you to turn the knob or use the key. These locks are usually found on older metal-framed patio doors, but can be a great option to secure wood or vinyl-framed sliding doors as well.
When you're examining your current patio door lock, make a note of the kind and size of the screw holes it uses to attach the escutcheon plate and lock body. This will help you pick a lock that has the proper screw holes. It's a good idea also to inspect your strike plate and make sure that it's secured properly.
If you have Jason Windows boltlock sliding doors from 2000-2009, make sure the screws that hold the door are secure and not loosened or missing. These screws hold the snib partially open in "vent" mode, which allows airflow, but also promoting security. They are also crucial to prevent your lock from being cut. All locks should be inspected and cleaned regularly to prevent corrosion, dust, dirt or debris from obstructing their operation.
If your snib broke you might be able to replace the entire strikeplate and snib. If your snib is just not aligned properly, you can make it right yourself by taking the strike plate off with the help of a putty knife. Then, back out the adjustment screw (located above and below the screw) to move the strike plate upwards or down until the engagement tongue lines up with the Milgard logo on the snib.